blog
7 Ways to Seal Holes in Roof to Stop Rats
Last Updated: November 7, 2026
Quick Summary
To seal holes in roof structures, match the material to the gap: pack coarse steel wool into cracks under 15 mm, fix metal mesh over openings of 15-50 mm, and use metal sheeting for holes over 100 mm. Always fix materials mechanically and keep vents open for airflow.
- A rat can pass through a gap around 15 mm wide, roughly the width of your thumb.
- Steel wool rusts when exposed to weather, so keep it in sheltered spots or use stainless steel outdoors.
- Fit mesh over vent openings rather than inside them so airflow continues and condensation is avoided.
- Foam is a backing only, because rats can chew through soft foam, so cover it with mesh or steel wool.
- Check the joint after a week because mortar shrinks slightly as it cures and may need topping up.
Table of Contents
- Signs of Rats in the Roof and Why Sealing Works
- How to Find Rat Entry Points Before You Seal Anything
- Best Materials to Block Rat Holes by Size and Location
- Method 1: Steel Wool for Small Gaps and Cracks
- Method 2: Metal Mesh and Hardware Cloth for Larger Openings
- Method 3: Seal Roof Tiles, Flashing and Eaves Gaps
- Method 4: How to Seal Gaps Around Roof Pipes and Vents
- Methods 5 to 7: Foam, Cement and Metal Sheeting Done Safely
- Frequently Asked Questions
Signs of Rats in the Roof and Why Sealing Works
Rats in the roof space are a common pest problem, and the fix almost always starts with blocking access. If you want to seal holes in roof structures properly, you first need to know what you are dealing with. Rats are creatures of habit. They use the same runways night after night, squeezing through gaps far smaller than most people expect.
A rat can pass through a gap around 15 mm wide. That is roughly the width of your thumb. This single fact explains why so many homeowners seal one obvious hole and still hear scratching a week later.
Noises, Droppings and Rub Marks to Watch For
Rats are nocturnal, so sound is often your first clue. Listen for scratching, scurrying or thumping in the early evening and just before dawn. Droppings are the other giveaway. Roof rat droppings are dark, pointed and about the size of a grain of rice. You may also spot greasy rub marks where fur brushes against timber, or gnaw marks on wiring and roof timbers.
Sealing works because it removes the rat's route in and out. Traps and bait deal with the animals present, while sealing helps stop the next wave.
Healthdirect Australia guidance on rodent-borne disease risks
How to Find Rat Entry Points Before You Seal Anything
Finding entry points is a slow, methodical job, and rushing it wastes your time later. Rats rarely use the front door. They exploit the edges: where roof meets wall, where pipes pass through, and where tiles lift.

A Step-by-Step Roof Inspection Checklist
Work through this list from the ground up:
- Check the roof line for lifted or broken tiles
- Look at flashing around chimneys and skylights
- Inspect eaves and fascia boards for gaps
- Trace every pipe and vent penetration
- Check the roof space for daylight showing through
- Follow cables and conduits into the building
- Look for gaps at wall-to-roof junctions
- Note any overhanging branches touching the roof
For a more detailed walkthrough, our guide on identifying rodent entry points in brick homes covers the trickier spots. If you want to confirm what you are seeing, this breakdown of signs of rodent activity in roof voids is a useful cross-check.
Best Materials to Block Rat Holes by Size and Location
The right material depends on three things: hole size, where it sits, and whether air needs to move through it. Rats chew through timber, plastic, foam and soft metals. They cannot chew through steel wool or heavy gauge mesh.
| Hole Size | Best Material | Where It Works | Airflow Consideration |
|---|---|---|---|
| Under 15 mm | Coarse steel wool packed tight | Cracks, tile gaps, small joints, mortar lines | None, solid fill is fine |
| 15-50 mm | Metal mesh or hardware cloth (6 mm aperture or smaller) | Eaves, vents, pipe surrounds, fascia gaps | Fit over the opening, not inside, so air still moves |
| 50-100 mm | Weldmesh plus foam backing | Larger gaps, wall-to-roof junctions, damaged soffits | Foam is backing only; mesh carries the barrier |
| Over 100 mm | Metal sheeting or cement board | Major openings, damaged sections, missing tiles | Solid panel, check the cavity is ventilated elsewhere |
Match the material to the job. Stuffing a large gap with steel wool alone will not hold. A few practical rules sit behind the table:
- Exterior versus interior. Steel wool rusts when exposed to weather.
- Foam is never the barrier. Expanding foam fills irregular shapes and sets hard, but rats can chew through soft foam. Use it as a backing behind mesh or steel wool, never on its own.
- Vents must stay vents. Roof spaces need ventilation to prevent condensation and timber rot. Cover vent openings with mesh fixed over the opening rather than packing the cavity, so airflow continues.
- Fixings matter as much as material. Staple, screw or nail mesh at multiple points and bend edges back so rats cannot work a corner loose. A mesh panel that flexes at the edge will be defeated.
- Sealant alone is not a barrier. Flashing sealant and construction adhesive suit small separations around flashing and skylights, but they are not a substitute for mesh or metal where a rat can apply leverage.
If you are unsure which material suits a particular gap, the safer default is mesh plus a mechanical fixing. It costs little more and removes the guesswork.
Method 1: Steel Wool for Small Gaps and Cracks
Steel wool is the go-to for tight spaces, and it works because rats cannot chew through it. Pack it firmly into cracks and gaps until it is dense. Loose packing gives the rat something to pull out.
Use coarse grade steel wool, not the fine stuff. Push it in with a screwdriver or blunt tool. For gaps under 15 mm, this alone is often enough. For anything larger, combine it with mesh behind it.
Watch out: steel wool rusts when exposed to weather. Keep it in sheltered spots, or use stainless steel wool outdoors.
Method 2: Metal Mesh and Hardware Cloth for Larger Openings
Metal mesh handles the mid-size openings that steel wool cannot fill. Cut it slightly larger than the hole, then fix it with staples, screws or nails.
Bend the edges back so the mesh sits flush. This stops rats from working a corner loose. For vents, fit the mesh over the opening rather than inside it, so airflow still moves.
Method 3: Seal Roof Tiles, Flashing and Eaves Gaps
Roof tiles, flashing and eaves gaps are the most common entry points we see. Lifted tiles create a gap a rat can exploit. Replace cracked tiles and reseat lifted ones. Check the flashing around chimneys and skylights, and seal any separation with a suitable flashing sealant.
Eaves gaps are the sneaky ones. Look along the fascia board where it meets the wall. Fill any gap with mesh or a solid strip. Trim overhanging branches back from the roof, because rats can use them as bridges.
Method 4: How to Seal Gaps Around Roof Pipes and Vents
Pipe penetrations and vents are a favourite rat highway. A pipe running through the roof leaves a collar gap, and rats squeeze through it. The fix is a metal collar or mesh wrap around the pipe, sealed at the base.
For vents, fit mesh over the opening and secure it well. Do not block airflow completely. Roof spaces need ventilation to prevent condensation and timber rot. If you are unsure how to seal gaps around roof pipes without trapping animals, check the roof space first for occupants.
Methods 5 to 7: Foam, Cement and Metal Sheeting Done Safely
These three methods handle the awkward jobs, irregular gaps, masonry, and large openings, but each has a failure mode that catches homeowners out. The common thread is that none of them should be used alone where a rat can chew or lever at the edge.
Method 5: Spray foam. Foam fills irregular gaps and sets hard. It is fast, but rats can chew through soft foam, so treat it as a backing rather than a barrier. Apply in thin layers and let each one cure before adding the next, because thick single passes stay soft in the centre. Once cured, trim it flush and cover the face with mesh or steel wool fixed mechanically. For exterior roof exposure, choose a foam rated for outdoor use and paint or seal it if the manufacturer specifies, since sunlight degrades many foams.
Method 6: Cement and mortar. Cement suits gaps in brickwork, around service pipes, and at wall-to-roof junctions where a solid, chew-proof fill is needed. Mix it to a firm consistency, wet enough to press in, dry enough to hold shape, then press it into the gap and smooth the surface. It sets solid and rats will not chew through it. It takes time to cure, so plan around the weather and protect fresh work from rain.
Method 7: Metal sheeting. For large openings, metal sheeting is the durable answer. Cut it to size, fix it over the hole with screws or nails at the edges and corners, and seal the perimeter with a suitable exterior sealant. This is the method for major damage or wide gaps where mesh alone would flex. Where the opening also needs airflow, fit mesh over a smaller vent cut into the sheet rather than leaving the whole panel open.
Before you seal anything, make sure no rats are trapped inside. Seal one hole, then watch for activity. If scratching continues, you may have sealed an animal in. For a full timeline on clearing an infestation, see how long it takes to get rid of rats.
If the problem keeps returning, our 7-step rat control plan and guide to when to call professional pest control will help you decide the next move. For hands-on help in the Perth area, Challenge Pest Control can inspect the roof, confirm the entry points and seal them properly.
Sealing a roof is fiddly work, and one missed gap undoes the lot. At Challenge Pest Control, we have handled rodent problems across Perth since 1987, and we know where rats get in. Our team offers free quotes and free advice, works 24 hours a day, seven days a week, and backs all work with a guarantee. We are fully insured and hold Public Health License 401.
Get started with Challenge Pest Control and seal your roof for good. Call 0422 926 291 to book today.
Frequently Asked Questions
How do rats get into a roof?
Rats reach roofs by climbing overhanging branches, downpipes, fences and power cables, then squeeze through gaps as small as 15 mm. Common entry points include lifted roof tiles, gaps in flashing, broken eaves, uncovered vents and spaces around service pipes. Once inside the roof space they nest in insulation and move through wall cavities into the rest of the house. Trimming vegetation back from the roofline and sealing these openings is the most reliable way to stop the cycle.
What is the best material to seal a hole to stop rats?
Steel wool works well for small cracks and gaps because rats cannot chew through it. For larger openings, metal mesh or hardware cloth holds up better than foam or filler alone. Match the material to the hole: steel wool for gaps under 15 mm, mesh for anything bigger, and metal sheeting for large damaged sections. Avoid expanding foam on its own, as rats can chew through it.
Can rats chew through expanding foam?
Yes. Expanding foam on its own is not chew-proof, and rats can gnaw through it. Foam is useful as a backing or filler around pipe penetrations, but it needs a physical barrier in front of it. Pack the gap with steel wool or metal mesh first, then apply foam or sealant to close the remaining space. This combination blocks airflow, keeps water out and gives rats nothing to chew through.
When should I call a pest controller or roofer about rats in the roof?
Call a professional if you cannot safely access the roof, if the damage involves structural timbers, or if rats keep returning after you have sealed obvious gaps. Working at height carries real risk, and some entry points sit under tiles or behind flashing that need a roofer to lift safely. Challenge Pest Control offers free quotes and advice. Call And Book Today on 0422926291.